Skip to content
Ring (562) 647-6550

Service · Whittier

Plumber for gas line work in Whittier

Gas piping is regulated work. This page explains what a plumber can run, cap, move or repair, why a permit matters, and what to do first if you smell gas.

Last changed

Ask for a quote

Gas meter, shutoff valve, earthquake shutoff valve and appliance in one line.

Smell gas right now? Put this page down and head outside. Once the building is empty, call the utility on its emergency line, 1-800-427-2200. Fire or danger means 911. Anything scheduled, whether a new line, a move or a repair, is reserved for a contractor who has a state license, working under a permit. We'll book a local plumber for Whittier and nearby service areas; the Rio Hondo Plumbing home page shows how.

Do plumbers actually work on gas piping?

Many do, though not every shop takes gas jobs, so ask first. Working on it takes a California contractor license, and most indoor gas piping also calls for a permit, then an inspection. SoCalGas runs the meter and its service valve. Everything downstream of the meter outlet is house piping, and that is the part a plumber touches.

SoCalGas supplies every city on our list, from Whittier out to Hacienda Heights, so the dividing line is the same everywhere. Pipe feeding your range, dryer, furnace, fireplace or water heater is yours to maintain. The meter is theirs.

Which gas jobs fall to a plumber?

Typical ones: a new branch to a range, dryer, grill, fire pit or fireplace; chasing down a leaking union; closing off an abandoned stub; shifting a line when a kitchen is redone; and replacing a flex connector. Larger projects include a gas run for an ADU or swapping out old steel pipe.

  • New appliance: range, dryer, tankless heater, pool heater, outdoor stub.
  • Repair: weeping union, corroded section, flex connector, a line nicked during digging.
  • Cap-off: sealing an unused stub, followed by a pressure test.
  • Relocation: rerouting around new cabinets or a laundry remodel.
  • Quake valves: fitting or resetting one, described in how to reset a quake shutoff.

A tankless heater burns a much bigger burst of gas than a tank unit, so check pipe diameter before you buy. Flexible gas line sizing explains the question.

Why do gas jobs require permits and a state license?

One poorly made joint can leak, and a leak can mean fire. Permitted work in California goes to a contractor who carries the state's license, and the permit brings an inspector and a pressure test before gas flows. Before anyone starts, search for the contractor in the state board's directory.

In Whittier the city's Building & Safety Division handles permits and inspections. Other cities run their own counters. Hacienda Heights, being unincorporated, goes through LA County Public Works. Have the plumber confirm the permit in writing and keep the signed inspection card.

Homeowner work ends here. Never thread, solder or tighten a gas fitting yourself, even for a faint weep. Residential gas piping codes puts the rules in plain language.

What do you do when you smell gas?

Don't flip switches or touch appliances, keep the phone in your pocket until you are outdoors, and skip any search for the source. Everyone walks out. Once you are a safe distance away, Emergencies go to 1-800-427-2200 at the utility. If something is burning or about to, ring 911 instead.

Four steps in order: no switches, walk outdoors, call the utility, call 911.

SoCalGas keeps its advice on the meter narrow. It should be shut only when you notice a whiff of gas, a hiss or any other hint of a leak, and only when reaching it is safe. Once shut, it stays shut. SoCalGas field employees alone reopen a meter. They also relight pilots, and piping should be checked for damage first.

Where do earthquake gas shutoff valves come in?

A quake valve shuts off the gas by itself when it detects strong shaking, which removes the largest fire risk after an earthquake. It sits apart from the meter valve. Putting one in is permitted gas work, and resetting one takes care because appliances and pilots need checking before gas returns.

SoCalGas allows owners to use the valve maker's reset instructions, yet it advises letting SoCalGas or a qualified professional perform the reset and inspect appliances. Read the reset walkthrough and the earthquake valve guide.

What decides the price of gas line work?

Length of run, whether it passes through a wall, attic or slab, pipe diameter, number of appliances sharing the line, and the permit fee. A short stub to a dryer is one extreme and an ADU branch the other. We won't name a figure without someone seeing the site.

Gas line costs breaks down the factors. A solid quote lists pipe material, permit, pressure test and wall or ceiling repair after the run goes in.

What should you ask before anyone starts?

Who applies for the permit? Who books the inspection? Which pipe material? Is the line sized for every appliance on it? Is a pressure test included? Jot down the license number the contractor gives you, then verify it before any cutting starts.

Warning signs: no permit line on the quote, a suggestion to skip the inspection to cut cost, or a plumber who cannot name the pipe size. For a deeper checklist, open choosing a gas plumber. When you want a price, ask here.

Book a plumber quote

Fill this in and we'll arrange a local plumber specialist to come and price the job.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who takes your job. You pay us nothing.

Common questions

Will a plumber run gas to a stove, dryer or fireplace?

Yes, if the plumber holds the right California contractor license and pulls a permit. The pipe gets sized for the appliance, run, leak-tested and inspected. Gas fireplaces and log sets raise venting and clearance questions, and the quote should answer them.

Can homeowners cap a gas line?

No. A cap has to be leak-tested, and permits usually apply. If you can reach the appliance valve, close it, then ring a plumber. Should a gas odor show up at any point, get outside, then call the gas company.

How can you spot a shady gas plumber?

Watch for a license number that is missing, a quote that is not in writing, a push for a large cash deposit, pressure to skip permits, and fuzzy answers on materials. A written contract is mandatory above $500. Check the license with the state's contractor board, and walk if the answers wobble.

Who handles a leak, SoCalGas or a plumber?

The meter and its service valve are SoCalGas's. Everything past the meter outlet, up to your appliances, is the owner's and gets repaired by a plumber. Leak at the meter: SoCalGas. Leak in the house piping: a plumber, once you have made the area safe.

In this section

  • 1/2 inch flexible natural gas line

    What a 1/2 inch flexible gas line is for, which pipe materials the plumbing code allows, burial depth, mobile home rules and why permits…

  • Gas lines

    When to shut your gas meter off after an earthquake, who may turn it back on, and how an automatic seismic valve gets installed by a local…

  • Gas lines

    How to reset an earthquake gas shutoff valve safely after it trips, when to call SoCalGas or a plumber, and how valve installation works.

  • Costs

    What a gas line costs: installation, repair, pipe materials, shutoff valves and permits, plus the safety rules that decide who may do gas…

References